RFlink gw dead?

Moderators: rtenklooster, Voyager, BertB, Stuntteam

Post Reply
Message
Author
devilkin
New user
Posts: 5
Joined: 07 May 2017, 22:03

RFlink gw dead?

#1 Post by devilkin » 18 Feb 2019, 21:36

Recently I started having some issues where my RFLink gateway would no longer respond to commands.

It was running an ancient fw, so I decided to update it using avrdude, but...

Code: Select all

         System wide configuration file is "/etc/avrdude/avrdude.conf"
         User configuration file is "/home/devilkin/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : /dev/ttyACM0
         Using Programmer              : stk500v2
         Overriding Baud Rate          : 115200
         AVR Part                      : ATmega2560
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    10     8    0 no       4096    8      0  9000  9000 0x00 0x00
           flash         65    10   256    0 yes    262144  256   1024  4500  4500 0x00 0x00
           lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : STK500V2
         Description     : Atmel STK500 Version 2.x firmware
         Programmer Model: AVRISP
         Hardware Version: 15
         Firmware Version Master : 2.10
         Vtarget         : 0.0 V
         SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x1e9801 (probably m2560)
avrdude: safemode: hfuse reads as D8
avrdude: safemode: efuse reads as FD
avrdude: reading input file "RFLink.cpp.hex"
avrdude: writing flash (199364 bytes):

Writing |                                                    | 0% 0.00savrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
Writing | #                                                  | 2% 10.67savrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
Writing | ##                                                 | 3% 21.02savrdude: stk500v2_recv(): checksum error
avrdude: stk500v2_recv(): checksum error
Writing | ##                                                 | 4% 21.35savrdude: stk500v2_ReceiveMessage(): timeout

...

This doesn't look particularly healthy.

Post Reply

Who is online

Users browsing this forum: No registered users and 20 guests