Any one successfully using "Aldi" BBQ Sensor (ET923)?

Post here about devices that are not yet or not fully supported

Moderators: rtenklooster, Voyager, BertB, Stuntteam

Post Reply
Message
Author
padrino
Normal user
Posts: 23
Joined: 17 Feb 2019, 15:05

Any one successfully using "Aldi" BBQ Sensor (ET923)?

#1 Post by padrino » 10 May 2021, 12:41

Hi there,

I am using one of these... (see photo below)
Works reliable for me, unfortunatelly I can't get it recognized by rflink.
With the loader programm in debug mode it shows up like a charm... :-/
Anyone else maybe able to get it to work and I am just unlucky? =)
GrillThermoAldi.jpg
GrillThermoAldi.jpg (189.93 KiB) Viewed 14536 times

User avatar
Stuntteam
Site Beheer
Posts: 786
Joined: 27 Jan 2016, 16:46

Re: Any one successfully using "Aldi" BBQ Sensor (ET923)?

#2 Post by Stuntteam » 10 May 2021, 17:27

It is not yet supported.
check http://www.rflink.nl/blog2/development
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

padrino
Normal user
Posts: 23
Joined: 17 Feb 2019, 15:05

Re: Any one successfully using "Aldi" BBQ Sensor (ET923)?

#3 Post by padrino » 10 May 2021, 20:03

I know it's name is not on the list but as sometimes devices are supported under different names, that was my hope, too...

I also sent some debug output in 2019, but never received feedback, maybe my mails don't come thru. 🤷‍♂️

So I thought about asking others, maybe I was too stupid... 😅

User avatar
Stuntteam
Site Beheer
Posts: 786
Joined: 27 Jan 2016, 16:46

Re: Any one successfully using "Aldi" BBQ Sensor (ET923)?

#4 Post by Stuntteam » 10 May 2021, 21:13

I will try to locate your mail...
-=# RFLink Gateway Development Team #=-
Introduction: http://www.nemcon.nl/blog2/
Generic Support forum: http://www.esp8266.nu/forum/viewforum.php?f=8

padrino
Normal user
Posts: 23
Joined: 17 Feb 2019, 15:05

Re: Any one successfully using "Aldi" BBQ Sensor (ET923)?

#5 Post by padrino » 11 May 2021, 00:53

👍

Just noticed, there was already a mail in 2018. 😅

I could re-send them, if that helps. 😊

Btw, subjects are (ok, I must admit, they probably could have been more distinct 🙄):

"New / improved device at 433mHz =)"

"RFLink with Renkforce - and "the" BBQ Thermometer"

padrino
Normal user
Posts: 23
Joined: 17 Feb 2019, 15:05

Re: Any one successfully using "Aldi" BBQ Sensor (ET923)?

#6 Post by padrino » 10 Jul 2021, 11:13

Stuntteam wrote: 10 May 2021, 21:13 I will try to locate your mail...
Hi there,

where you able to locate my emails?
If not, just tell me how I can further help.
If needed I can also resend them. =)
Any other assistance needed? Just tell me. :)
Thanks for investigating.

Have a nice weekend,
padrino

Post Reply

Who is online

Users browsing this forum: No registered users and 17 guests