Let's Control It

Dick60

I switched to the esp8266 because it is more convinient for me to test the sensor. I use A0 port and connected a 10k potmeter to 3.3vplus, to the GND and in the middle to A0. Als paralel to the potmeter I connected the Sensor. Turning the Potmeter I see a change in messurments but putting the sensor...

Dick60

I tried to get this device working on an esp8266 and an esp32 (preferable) but did not had any sucees in it. I use the ESPEasy_binaries27042022 and connected the soil moister sensor to the 5v, Gnd and an Analog port (in my case on the esp32 pen nr 25 (ADC2-ch8). Also put the sensor in some soil. No ...

Dick60

the settigs are now
- Force WiFi B/G: checked
- Periodical send Gratuitous ARP: checked
- Max WiFi TX power: 20,5
- Use Last Connected AP from RTC: unchecked

Dick60

perfecto, thanks both for the support, no frustration from my side anymore

Dick60

ok, this is the info requested
802.11g (RSSI -54 dBm)

Dick60

Chromo 23 is the solution TD-er mentioned the same as yours?

Dick60

It took some time because of the "Hard to connect" issue. I changes the settings to: - Force WiFi B/G: checked - Periodical send Gratuitous ARP: checked - Max WiFi TX power: 20,5 The max of the " Max TX power" was 20,5 so i changed it to that higher level. First test show a succe...

Dick60

is this what you asked for, rssi? Force WiFi B/G: false Restart WiFi Lost Conn: true Force WiFi No Sleep: true Periodical send Gratuitous ARP: false Connection Failure Threshold: 0 Max WiFi TX Power: 17.50 Current WiFi TX Power: 14.00 WiFi Sensitivity Margin: 3 Send With Max TX Power: true Extra WiF...

Dick60

I am sorry, it was early and was frustrated about a unit that did not work suddenly. I know my Ip number of the unit, password is known and set. After starting one of my browsers, mentioned above, enter my ip number of the unit and need to refresh, most of the time for 10 minutes, until the user int...

Dick60

Can somebody explain why it is so difficult to get connected to the user menu of an ESPeasy node. I use the latest firmware on a esp 8266. I am using a Windows 10 laptop for accessing. Al browsers show the same difficult acess (IE, Edge, Firefox and Brave). Hope to hear if anyone has a solution.

Dick60

I tested it and it works as expected. Thanks for the very very good service you delivered.

Dick60

That is what I did, copied it in the latest release (20210802) bin folder, strted the flasher and selected the .bin you send to me. Finished succefull but as soon as I want to add the MP3 device, it is not in the list. Any idea or what am I doing wrong.

Dick60

I am sorry, I don't understand, which BIN do i need to load to test the results?

Dick60

Perhaps a stupid remark, is it ready for testing? Is the option for volume level, mentioned before not possible using rules? On System#Boot do [u][b]vol,10[/b][/u] play,255 // file number 255 timerSet,1,30 //play the song for 30 seconds (this is a generic command!) Endon On Rules#Timer=1 do Stop End...

Dick60

both solutions are working so I can make a selection. Thanks for the support

Dick60

Thanks foor the reply but what I wanted is that I have 2 moments in time, say 13:00 and 17:00. On those moments I want to start the timer but only is the Holiday switch is active and if not active, It will not start the timer.

Dick60

I am strugling to get this rule operational. I use the latest firmware on my Nodemcu. At this moment this rule execute on time, defined in the rule but doesn't take notice on the "Holiday#State]=1" option. How can I fix that? On Clock#Time=All,**:** do // every day at **:** hours do If [Ho...

Dick60

The MP3 is working perfectly using the "normal control options mentioned in the WIKI. A nice, missing function, would be the option to put the volume and the Play number in a rule. Bur for now I m happy with it and thiefs are welcome with the sound of barking agressieve dogs.

Dick60

I use the keypad relay, so the donglesare stored in your keypad and if the correct dongle is used, the relay in the keypad is activated. Use that signal for your ESP.

Dick60

I have such a keyboard in use already for serveral years and works great. If you use the same power sourse for both the keyboard and your Arduino devive, you can use the "-(minus)"of the relay on the keyboard PCB.

Dick60

thank you for the effort. I appreciate it.

Dick60

this is all above my level of knowledge. Probably I use Variables for now to monitor the mp3's already played and that the new play not start Always with the same mp3. This is part of my alarm system (barking dog) and you do not want to start with the same mp3 but "randomly".

Dick60

I've tested the new command MODE as described in your previous answere. The PLAY option is working but the MODE,3 without the "control?cmd=" (http://xxx.xxx.x.xx/mode,3) is not working for now. Probably I have to wait for the final version of the plug-in.

Dick60

I hope, there is no misunderstanding from my side, I have load the attached Bin on my NodeMcu without any problems, created the device DFPLAYER-MINI and tested the play mode (http://xxx.xxx.x.xx/control?cmd=play,3). Worked perfect. Tried the new option MODE at boot On System#Boot do vol,10 mode,3 de...

Dick60

thanks for the explanation. At the moment I use the test.bin because that was the only bin where the MP3 player was available. What i need in my project is the mp3 player and some normal switches. I appreciate the offer, to make an costum test.bin for me. After a succesfull implementation I can give...

Dick60

I use the PFplayer mini on my ESP8266 device with the latest rom.It works great but is there a a rule to start playing the playlist like a Lucky shot, so not sequently but randomly?

Dick60

ha ha, I didn't know. That explain everything. Thanks for the info and for you a "zeer voorspoedig 2021" ( a happy new year.

Dick60

The message is now visible in the log.
Was trying other settings, in Tools/Advanced Settings/Rules Sttings I selected "Old Engine". That solved the Timer issue. Now it works but I do not like I do not know WHY!!!.
I hope you can explain.

Dick60

re sult was an "OK". Sorry I did not mentoned it. ( I hope this is what you expected).

Dick60

but if I add the log option to this part of the timer

Code: Select all

On Rules#Timer=1 do
GPIO,15,0
LogEntry,"In Timer 1 handler"
endon

It never arrivés in the log

Dick60

Domoticz: Sensortype: 1 idx: 536 values: 0 14489: ULTRASONIC : TaskNr: 1 state: 1 14498: EVENT: Keukenradar#Distance=1 14521: ACT : GPIO,15,1 14523: GPIO : port#15: set to 1 14525: ACT : timerset,1,30 14529: ACT : LogEntry,'In Timer 1 handler' 14531: In Timer 1 handler 14951: SW : GPIO=15 State=1 Ou...

Dick60

Good point, to reduice the margin of error I deactivated the HTTP connection. I use Domomticz, where I use a switch for a manual mode (during a holiday. In that case I use the timerswitch with some restrictions using the IF commands. But that is out of scope for now. For now this is the Log without ...

Dick60

The wiring is quite simple. GPIO 8 is directly connected to a relaisboard. If I send a GPIO,15,0 it turns off. Included you find also a part of my log: 1921626: EVENT: Keukenradar#Distance=0 1922827: WD : Uptime 32 ConnectFailures 0 FreeMem 18056 WiFiStatus WL_CONNECTED ESPeasy internal wifi status:...

Dick60

I installed the 27 dec build. Now I found that mij timer is not working. In turn ON the GPIO 15 but does not turn it off after 30 seconds Does anyone see what I am doing wrong? On Keukenradar#Distance do if [Keukenradar#Distance]=1 GPIO,15,1 timerset,1,30 endif endon On Rules#Timer=1 do GPIO,15,0 en...

Dick60

TD-er wrote: ↑22 Sep 2020, 11:08 Plugin 065 (DRF0299) should be included in the "testing" build.
It should be listed as "Notify - DFPlayer-Mini MP3 [TESTING]" in the plugin list when adding a new task.

How to load and where can I can the "testing" build?

Dick60

I join to. It is not clear for me. I wanted to add a DFPlayer. The plugin in located in P065_DFR0299_MP3. Hope you can give us an explanation.

Dick60

it is not the model you asked for but have 2 Asus tr-ac5300 as a Aimesh netwerk and works very stable already for years both for DOMTICZ and ESPEASY.
Good luck with your search

Dick60

Thanks a lot for all the support. Now it makes sence to implement it in my project.
Have a great day.

Dick60

this is working
On switch1#State do
GPIO,14,[switch1#State#Z]
endon

but how can I use the 'OR'' statement
if switch1=1 or switch2=1

the Generalswitch must be set to 1

Dick60

is this the way to continue???? It does not work but advise please.

On switch1#State do
if [switch1#State]=1
event,generalswitch
endif
endon

On generalswitch do
if [switch1#State]=1
gpio,0,1
else
gpio,0,0
endif
endon

Dick60

no there isn't a 'generalswitch' task. What I read in the wiki is that it is possible to use this kind of rule. Wrong intepretation. So what si the approch for me, do you have an example for me how to het this working?

Dick60

Sorry forgot to mention, the latest one 15052020

Dick60

According the WIKI I can you the 'OR' statement in rules. on test do if [test#a]=0 or [test#b]=0 or [test#c]=0 event,ok else event,not_ok endif endon I adjusted the example to my needs but it does not work. Can anybody help me around? I have 2 switches I can make them 1 or 0. Depending the status it...

Dick60

deleting the ESPeasy from my known wifi network list did the job. The password espconfig is the correct one. For all, thanks for the support! I continue with my build! Have a nice day and a lot of fun!

Dick60

Forgot to mention, tried that password as well withou any positive result. Just unpacked my last NodeMCU, loaded the 1 Mb blank and after that the normal 1 Mb (the one 20201003) no better result.

Dick60

Tested again tris morning. a brand new NodeMCU and a D1 both the same result, Password 'espconfig' incorrect. Because they are brand new, corrupte memory could not be the reason.

Dick60

Unfortunately the sam result. What I did: New MCU Blank_4Mb, after finishing loaded a blank_1Mb, after finishing loaded the normal_8266_1Mb. Also tried blaNK_ 4Mb and after that the normal_8266_1Mb. Same as previous but than all with the 4Mb version. All the sam results

Dick60

What I did with my Nodemcu, It was an already in use MCU, loaded the "blank 1 MB" option, after finish loading (without reseting), loaded the "Normal_esp8266_iM.bin". Finished loading, disconneted the module, connect to ESPWIFI en get the password request. That is what I did.

Dick60

Sorry but did not work for me. Still get the message "wrong password". Tried a 2nd NodeMCU but same result. Found a temporay solution, I loaded a Dec2018 version and was able to connect without a wifi password. I can continue for now but if one of you have any suggestions, pls let me know.

Dick60

After finishing flashing my ESP (several models) with the latest firmware release (but also previous firmware versions),using the ESP.Easy.Flasher.exe opened as admin, I want to connect to the ESPWIFI network to config it. I get a WIFI security message that I must add a password (which password). In...

Search found 243 matches