Search found 81 matches
- 24 Jan 2024, 11:56
- Forum: ESP Easy: General Discussion
- Topic: PWM frequency esp32
- Replies: 16
- Views: 2140
Re: PWM frequency esp32
There is a 500 ohm trim resistor on the motherboard. it is replaced with a variable resistor and installed on the panel of the induction cooker. the resistor is set to low voltage. with its help I can smoothly adjust the power at each stage, that is, at the 2500 watt stage can regulate from (approxi...
- 24 Jan 2024, 08:13
- Forum: ESP Easy: General Discussion
- Topic: PWM frequency esp32
- Replies: 16
- Views: 2140
Re: PWM frequency esp32
I read about the principle of operation of an induction cooker and concluded that not everything is so simple. and adjust frequency, voltage and duty cycle. All this can be done, but in my case the result is not worth the effort. I decided to do without the ESP, and just install a variable resistor ...
- 22 Jan 2024, 06:30
- Forum: ESP Easy: General Discussion
- Topic: PWM frequency esp32
- Replies: 16
- Views: 2140
Re: PWM frequency esp32
thanks for support. I think that a variac is not suitable for these purposes, and power adjustment is performed using a microcontroller using control buttons. Therefore, in order to change the adjustment step, I need to change the microcontroller firmware, and I’m unlikely to succeed. first I need t...
- 21 Jan 2024, 07:00
- Forum: ESP Easy: General Discussion
- Topic: PWM frequency esp32
- Replies: 16
- Views: 2140
- 21 Jan 2024, 06:55
- Forum: ESP Easy: General Discussion
- Topic: PWM frequency esp32
- Replies: 16
- Views: 2140
- 20 Jan 2024, 21:03
- Forum: ESP Easy: General Discussion
- Topic: PWM frequency esp32
- Replies: 16
- Views: 2140
Re: PWM frequency esp32
I haven’t taken frequency measurements on my induction cooker yet. but there is a desire to buy an inexpensive induction cooker and do experiments on it, and if the experiment is successful, then modify my cooker.
- 20 Jan 2024, 13:22
- Forum: ESP Easy: General Discussion
- Topic: PWM frequency esp32
- Replies: 16
- Views: 2140
Re: PWM frequency esp32
ок. Thank you. The question is related to the fact that I have an induction cooker, but its power adjustment has a wide step (1000-1300-1500-1800-2100-2500-3000-3500) and I want to make a smoother power adjustment. I'm wondering whether it will work or not
- 20 Jan 2024, 09:37
- Forum: ESP Easy: General Discussion
- Topic: PWM frequency esp32
- Replies: 16
- Views: 2140
PWM frequency esp32
Good afternoon. I have a simple simple question that doesn't require a long discussion. Since I couldn’t find a topic where I could ask such questions, I decided to create one. here is my question: what is the maximum PWM frequency that the esp32 can provide? Is it possible to use esp32 with espeasy...
- 29 Nov 2023, 14:02
- Forum: ESP Easy: Projects / Applications
- Topic: ESP32: Port to dimming via PWM?
- Replies: 16
- Views: 4084
- 29 Nov 2023, 12:48
- Forum: ESP Easy: Projects / Applications
- Topic: ESP32: Port to dimming via PWM?
- Replies: 16
- Views: 4084
- 29 Nov 2023, 09:34
- Forum: ESP Easy: Projects / Applications
- Topic: ESP32: Port to dimming via PWM?
- Replies: 16
- Views: 4084
Re: ESP32: Port to dimming via PWM?
Good afternoon. can you help with this? I need to regulate the rotation speed of an asynchronous motor using a PWM, but for this I need to control the zero crossing. can you give me a diagram?
- 05 Nov 2023, 16:01
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
my version also works, but yours is probably more reliable. Thank you
- 05 Nov 2023, 08:41
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
did it differently On Rules#Timer=1 Do If [datchik#Total]<=4999 And [plugin#gpio#pinstate#19]<=900 Let,3,[plugin#gpio#pinstate#19]+50 PWM,19,[int#3] Elseif [datchik#Total]>=5000 And [plugin#gpio#pinstate#19]>=100 And [var#4]=0 Let,3,[plugin#gpio#pinstate#19]-25 PWM,19,[int#3] Elseif [datchik#Total]>...
- 03 Nov 2023, 19:45
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
Good afternoon. I have sliding gates. I need the gate to start moving smoothly and end moving smoothly.there is a pulse counter on the motor. and everything is fine when the gate moves from start to finish, that is, the gate starts moving smoothly and slows down before stopping.but if you stop the g...
- 24 Sep 2023, 13:49
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
I also thought about LDR when I wrote the previous question. Thank you. And I apologize for the off-topic questions.
Maybe it's worth creating a topic about one-time questions
Maybe it's worth creating a topic about one-time questions
- 24 Sep 2023, 11:56
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
again and just try to 'emulate' the potentiometer. That's just a DC analog value, which can be easily generated via ESPEasy. Either via one of the ESP32 DAC pins, or send a PWM signal and add some resistor + capacitor to make the value more stable. please tell me how to remove the potentiometer in ...
- 14 Sep 2023, 13:29
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
This is a sliding gate drive. It's fully functional, but I wanted to control the gate via the Internet. Therefore, I decided to change the standard microprocessor to ESP32. It is necessary to regulate the rotation speed of the motor so that the gate does not hit the gate trap. that is, the speed mus...
- 14 Sep 2023, 09:45
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
ESPEasy is probably not fast enough to respond to this using rules that is, I won’t be able to change the rotation speed? What options are there to solve my problem? The diagram was taken from the Internet, I had a ready-made board, but it was similar to the one I showed. there was a processor MEGA...
- 14 Sep 2023, 08:59
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
Good afternoon. I'm trying to change the speed of an AC motor to 220 volts. I connect via a triac according to this scheme Безымянный.png I'm writing a simple rule On bot#State=1 Do PWM,27,1 Endon and the motor rotates at maximum speed. that is, the rotation speed is always maximum, regardless of th...
- 28 Jul 2023, 11:03
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
There should not be a difference. However when comparing numericals like "> 01" in your rules, it is best not to have a leading zero. The number parsing in ESPEasy is done using a more elaborate function which will not consider octal numbering. But I'm not 100% sure all compares use this ...
- 28 Jul 2023, 10:20
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
Good afternoon. Is there a difference in coding between the two rules? on Clock#Time=All,**:** do if [int#9] = 0 if %sysmin% >= 01 asyncevent,startDisinfection endif endif endon on Clock#Time=All,**:** do if [int#9] = 0 AND %sysmin% >= 01 asyncevent,startDisinfection endif endon
- 21 Jun 2023, 19:39
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
Good afternoon . maybe it will be useful and interesting for someone. here I asked a question about the work of the rules and could not understand why they do not work it was all about writing the rules, more precisely the use of spaces and = and>/< it was On Rules#Timer=4 do //salt pump operating m...
- 03 Jun 2023, 13:03
- Forum: ESP Easy: General Discussion
- Topic: firmware changes
- Replies: 5
- Views: 1165
Re: firmware changes
you should see only 1 DNS entry on the sysinfo page (the now I have 2023-06-03_13h57_33.png . and at the moment everything is working (Build: ESP_Easy_mega_20230409_neopixel_ESP32_4M316k Apr 9 2023) but on the other firmware the settings were the same, but after a couple of days the module losted c...
- 03 Jun 2023, 09:25
- Forum: ESP Easy: General Discussion
- Topic: firmware changes
- Replies: 5
- Views: 1165
- 02 Jun 2023, 15:22
- Forum: ESP Easy: General Discussion
- Topic: firmware changes
- Replies: 5
- Views: 1165
firmware changes
Good afternoon. used normal Build20230409_20230531075113 there was a sensor ds18b20, but there was a problem with wifi. after two or three days of work, wi-fi was disconnected and the module had to be rebooted. I thought it was the firmware and decided to change . because on another module I use Bui...
- 19 May 2023, 08:26
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
into this: THANKS FOR THE HELP almost 1000 characters shorter :) and if I want to do this action 6 times a day, can I add one more hour? What is the data limit? for example is it possible? if (%syshour% = 1 or %syshour% = 6 or %syshour% = 11 or %syshour% = 16 or %syshour% = 21 or %syshour% = 23) an...
- 18 May 2023, 09:43
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
Good afternoon. there is such a code. on Time#Initialized do If %systm_hm_0% <= 22:00 And %systm_hm_0% >= 01:00 gpio,33,1 gpio,12,1 else gpio,33,0 endif If %systm_hm_0% >= 01:00 And %systm_hm_0% <= 01:25 GPIO,27,1 TimerSet_ms,1,2500 TimerSet,3,60 else gpio,27,0 endif If %systm_hm_0% >= 06:00 And %sy...
- 10 May 2023, 09:19
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
electronics say that this is possible because of the mosfet, but this is unlikely. All the same, I will change the mosfets to others and I will observe.
- 09 May 2023, 14:29
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
I see the pins you mentioned are all set to 0 when this event happens: up#gerkon=1 It seems to me that this is not connected, since the cable is only 1.5 meters long and the failure occurs exactly at the moment when 19.13 and 21 should turn 0 (at the moment when timer 2 should be activated). that i...
- 09 May 2023, 13:34
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
Are you still using the same rules as you posted on the 30th of April ? The rules are the same, only the GPIOs numbers have changed. but just in case on Time#Initialized Do LoopTimerSet_ms,5,1000 Endon On Rules#Timer=5 do TaskValueSet,11,1,[plugin#gpio#pinstate#13] TaskValueSet,9,1,[plugin#gpio#pin...
- 09 May 2023, 12:55
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
IMG_20230509_133519.jpg schematically depicted only one area, since GPIOs 13,18,19,21,26,32 are the same What do you mean by "disconnects all GPIOs" ? Does the unit reboot? Or is it completely unresponsive? good day. that is, switches the state GPIOs 13,19,21 and 26 from 1 to 0, although ...
- 08 May 2023, 09:41
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
could it be due to multiple concurrent tasks? Maybe needed to optimize the rules?
- 08 May 2023, 08:52
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
- 01 May 2023, 13:46
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
ок. Thank you! I'll try to change 12.16 and 17
- 01 May 2023, 11:11
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
For ESP32 it is a completely different story I forgot to say that I have exactly ESP32. but there is no problem with booting the module. that is, I turn on the module, it booting and waits for one of the conditions of the rules to come. the module fulfills the initial rules well, for example, when ...
- 01 May 2023, 08:38
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
Is it possible that the unstable operation of the module is related to the use of gpio 5 and 12?
although there were never any problems loading the module.
now I tried several times to emulate the problem, but the module worked correctly.
although there were never any problems loading the module.
now I tried several times to emulate the problem, but the module worked correctly.
- 30 Apr 2023, 17:41
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
Good afternoon. please see my rules. on Time#Initialized Do LoopTimerSet_ms,5,1000 //this is just for monitoring Endon On Rules#Timer=5 do TaskValueSet,11,1,[plugin#gpio#pinstate#13] // salt pump rotation speed TaskValueSet,9,1,[plugin#gpio#pinstate#17] //sound alarm (Buzzer) Endon On up#gerkon Do i...
- 28 Apr 2023, 12:46
- Forum: ESP Easy: General Discussion
- Topic: Rule timer
- Replies: 4
- Views: 4275
Re: Rule timer
thank you
- 28 Apr 2023, 09:22
- Forum: ESP Easy: General Discussion
- Topic: Dummy TaskValueSet from examples not working
- Replies: 10
- Views: 1247
- 28 Apr 2023, 08:27
- Forum: ESP Easy: General Discussion
- Topic: Dummy TaskValueSet from examples not working
- Replies: 10
- Views: 1247
Re: Dummy TaskValueSet from examples not working
your third timer starts the third timer? i.e. itself?
Do you also have the setting enabled : tools>Advanced Settings>Allow TaskValueSet on all plugins ?
Do you also have the setting enabled : tools>Advanced Settings>Allow TaskValueSet on all plugins ?
- 28 Apr 2023, 08:14
- Forum: ESP Easy: General Discussion
- Topic: Rule timer
- Replies: 4
- Views: 4275
Re: Rule timer
Good afternoon. how many timers can be put in the rules now? at the moment I am using 8 timers, how many more timers can I set up for the module esp32 to work properly?
- 26 Apr 2023, 12:49
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
Thank you. for now I'll leave it as it is. I will watch
- 26 Apr 2023, 12:07
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
and yet I don’t understand why this option is bad, except that a short press will work after one second
Code: Select all
on qq#qq=1 do
TimerSet,1,1
Endon
On Rules#Timer=1 do
GPIO,16,1
TimerSet,1,0
endon
on qq#qq=11 do
GPIO,17,1
TimerSet,1,0
endon
- 26 Apr 2023, 11:59
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
- 26 Apr 2023, 10:08
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
I guess not. Yeah. not so simple :D thank you. i have three options : how i did on qq#qq=1 do TimerSet,1,1 Endon On Rules#Timer=1 do GPIO,16,1 TimerSet,1,0 endon on qq#qq=11 do GPIO,17,1 TimerSet,1,0 endon as suggested to me On qq#qq Do If %eventvalue1%=1 let,1,0 Elseif %eventvalue1%=11 GPIO,17,1 l...
- 25 Apr 2023, 18:09
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
Good afternoon. I have a problem again but this time with a long button press. I have a simple rule On qq#qq Do If %eventvalue1%=1 GPIO 16,1 Elseif %eventvalue1%=11 GPIO 17,1 Endif Endon but with a long press, it works first GPIO16 and only then GPIO17. please tell me how to fix it somewhere I found...
- 23 Mar 2023, 05:37
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
- 22 Mar 2023, 15:55
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
- 22 Mar 2023, 14:23
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
- 22 Mar 2023, 14:09
- Forum: ESP Easy: Projects / Applications
- Topic: Rules in ESPeasy
- Replies: 137
- Views: 33855
Re: Rules in ESPeasy
thank you for your patience and help. but i have a new problem :mrgreen: On garag#analog Do If %eventvalue1% < 999.00 And [plugin#gpio#pinstate#25] <= 1010 Let,1,[plugin#gpio#pinstate#25]+20 PWM,25,[int#1] Elseif %eventvalue1% > 1000.00 And [plugin#gpio#pinstate#25] >= 500 Let,1,[plugin#gpio#pinstat...