unfortunately in commit 17ba610d "Merge pull request #4285 from TD-er/bugfix/wifi_mode_multiple_times" it does NOT take action.
there is again no connect possible and Ping loss is around 100%.
Commit 5bdfc81b (pull request #4285) merged into 14fb3a2e was fine!

Gregor54321 wrote: ↑24 Oct 2022, 15:26 Runs smooth (2% loss) on the S-B R2 V1 testboard.

0,05% after 13k pings...

in the local repositories directory did the trick...
I didn't not know about the separate Dev-Repo...
Runs smooth (2% loss) on the S-B R2 V1 testboard. I will now reflash my fuse panel.

@TD-er: May you can pre-release a patch? Or are you go to push it to a branch I would be able to merge/cherrypick for myself?
Thanks a lot!

my device is "Sonoff Basic R2 V1.0 (2017-10-11)"

wifidisconnect does it! INIT : Booting version: ESP_Easy_mega_20221006_normal_ESP8266_4M1M, (GitHub Actions) HEAD_a81d6ed (ESP82xx Core 2843a5ac, NONOS SDK 2.2.2-dev(c0eb301), LWIP: 2.1.2 PUYA support) 5496 : Info : INIT : Free RAM:25984 5498 : Info : INIT : Cold Boot - Restart Reason: Power On 549...

Do you have "eco mode" enabled? it's not enabled Was there an AP active on the ESP? unfortunatelly no But it was able to use the saved wifi credentials from former flash. After erasing flash and reflashing your image, no AP comes up (Wifiscanner does not detect any new wifi), as it seems ...

Next try: stable after 6min...
WebUI/advanced says: "Current max: 14.00 dBm"

Now it becomes strange:
New reboot. Ping statistics for monitoring progress over time...
A lot of ping loss until 22min after reboot, then 0% loss...
No special entries / abnormalities in serial log! (no change of AP, simply nothing!)

TD-er wrote: ↑17 Oct 2022, 22:42 Can you try this test build: https://github.com/letscontrolit/ESPEas ... 3265472808

Awsome! Right Track!
0% Loss starting 22mins after reboot (initially same poor performance as before). Will try to find the parameter for that difference...

Seems not to be as bad as afraid... This small deviation should have no effect at all for such short transmissions. 4218 : Info : NTP : NTP replied: delay 30 mSec Accuracy increased by 0.389 seconds 4220 : Info : Time set to 1666040855.389 4221 : Info : Current Time Zone: STD time start: 2022-10-30 ...

Just flashed a custom image with wifi infos from recent commit d34770a*. Within the first around 120sec ping loss is acceptable with 10-20% but then suddenly loss is sharply rising to >99%. Will provide log tomorrow. Maybe there are already some infos about the drift in there. Will have a look into ...

Could you please also test this GH Actions test build as soon as it is finished? https://github.com/letscontrolit/ESPEas ... 3200480365 Perhaps this build may run stable on your Sonoff Basic node. I did add some delays in starting the WiFi which may give the Sonoff Basic power supply slightly more ...

Sorry I haven't read along here for a while. I'm very busy at work at the moment... I have a smaller measurement park to do extensive measurements during runtime. Which parameters should be determined under which circumstances? I have already changed the flash chip for a 4MB version too. And it seem...

I know Thomas also had some issues with these Sonoff Basic units. Extremely fascinating: I own some Sonoff S26 WallPlugs. I applied a current build onto one of them: 1200pings in 10min without loss. I put the same image.bin onto the SonoffBasic and have 90% packet loss. As it seems, it indeed may b...

TD-er wrote: ↑02 Oct 2022, 19:34 Which build did work?
And if it is a different firmware, which SDK was it using? (or build date if known)

A build where I did not take notice of that problems was 20104-Mega (selfbuild 2019.11.29) No more infos available, it is reflashed now...

Ath wrote: ↑02 Oct 2022, 19:29 Ah, the infamous Sonoff Basic, with the notoriously (or should I say dramatically?) poor WiFi performance, mostly caused by the low-end power-supply for the ESP

is powered by USB

Ath wrote: ↑02 Oct 2022, 19:03 Can you share a photo of the ESP board, especially the antenna area? As this sounds like either a weak/poor antenna mount, or the ESP interfering with the WiFi signal (even though the signal strength seems ok)

The device is standardised. And with different firmware packet loss less.

Ah... WMM found...

Can you do some more tests with the last commit I pushed to that PR? https://github.com/letscontrolit/ESPEasy/pull/4285 The Github Actions build for it is almost done: https://github.com/letscontrolit/ESPEasy/actions/runs/3169070595 This last change does show this in the Fritzbox details section of...

Hmm the fact you can even run spec_debug_custom_ESP8266_4M1M is really surprising to me. That one is only meant to be used by me for running PVS Studio to perform static analysis of the code to find bugs. (I do have a license for PVS Studio) Well, I'm with PlatformIO inside VSCode on Linux. And spe...

Hi. First I have since some time problems like - Disconnected! Reason: '(6) Not authed' - Disconnected! Reason: '(202) Auth fail' - Disconnected! Reason: '(2) Auth expire' Then I noticed, there are a lot of packet losses with all kind of builds: - custom_alt_wifi_ESP8266_4M1M - custom_ESP8266_4M1M -...

When woken up, is it possible to recognize the reason for wakeup event? Hypothesis: a) when woken up by GPIO16 timer the timers value is "0" (if decreasing for interrupt) OR timer is at or sligthly above compare-value (if increasing for interrupt) b) timer is neither 0 nor at compare-value...

Hi all! I modified an ESP01S (8266) with only GPIO0, GPIO2, RST, Rx, Tx, ChipEn by default connected. I soldered additional connections to ADC/TOUT and GPIO16, so I was able watching for battery voltage and periodically waking via RST by SleepTimer. But how can I perform different actions by pressin...