Search found 6 matches
- 20 Mar 2022, 20:46
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 10811642
Re: Support for PZEM 004T Energy monitor
Thanks, it works great for now. only kWh need to be converted to Wh for P1 meter ( Domoticz) thanks for the reply. in espeasy pzem settings d1 and d2 are not allowed Menu Hardware -> I2C Interface -> GPIO ⇄ SDA = None / GPIO → SCL = None Then, D1,D2 will be available. (Same for D9-Rx/D10-Tx in Tools...
- 16 Feb 2022, 15:37
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 10811642
Re: Support for PZEM 004T Energy monitor
Thank you very much thanks for the reply. in espeasy pzem settings d1 and d2 are not allowed Menu Hardware -> I2C Interface -> GPIO ⇄ SDA = None / GPIO → SCL = None Then, D1,D2 will be available. (Same for D9-Rx/D10-Tx in Tools->Advanced -> uncheck "Enable Serial port")
- 13 Feb 2022, 22:33
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 10811642
Re: Support for PZEM 004T Energy monitor
@mojso Supply PZEM with 5V directly (as your first schematic. No 1k requested). But don't use D3 and D4 for communication because these pin can prevent ESP to boot. D1,D2 can be used in place. thanks for the reply. in espeasy pzem settings d1 and d2 are not allowed maybe D6 and D7 will be ok to use...
- 13 Feb 2022, 18:38
- Forum: ESP Easy: Hardware
- Topic: Support for PZEM 004T Energy monitor
- Replies: 309
- Views: 10811642
Re: Support for PZEM 004T Energy monitor
how to connect wemos d1 mini properly with pzem 004T v3.0 100A? schematic rx / tx as in this picture
can i use 3.3v with the same schematic or do I need a
1k ohm resistor, from the 5v pin in the optocoupler
Or
can i use 3.3v with the same schematic or do I need a
1k ohm resistor, from the 5v pin in the optocoupler
Or
- 06 Jan 2021, 21:56
- Forum: ESP Easy: General Discussion
- Topic: Ir Transmitter ?
- Replies: 0
- Views: 22232
Ir Transmitter ?
how to send this raw codes or how to convert it to raw2 http://192.168.1.102/control?cmd=IRSEND,RAW, .... // ON/OFF (toggle): uint16_t TOGGLE[21] = {6680, 2412, 3374, 1560, 920, 732, 918, 1594, 1720, 758, 894, 1584, 896, 732, 920, 1558, 1748, 758, 1722, 1584, 1720}; // UNKNOWN 9EB58962 // Power Up (...
- 06 Jan 2021, 20:54
- Forum: ESP Easy: Hardware
- Topic: IR Transmitter ?
- Replies: 120
- Views: 198739
Re: IR Transmitter ?
how to send this raw codes or how to convert it to raw2 // ON/OFF (toggle): uint16_t TOGGLE[21] = {6680, 2412, 3374, 1560, 920, 732, 918, 1594, 1720, 758, 894, 1584, 896, 732, 920, 1558, 1748, 758, 1722, 1584, 1720}; // UNKNOWN 9EB58962 // Power Up (flame up): uint16_t P_UP[19] = {6778, 2336, 3446, ...