Search found 578 matches

by enesbcs
21 Oct 2021, 13:47
Forum: ESP Easy: Software
Topic: Serial MCU controlled relay/switch
Replies: 455
Views: 506410

Re: Serial MCU controlled relay/switch

The Arduino code according to on byte open [] = {0xA0, 0x01, 0x00, 0xA1}; Serial.write (open, sizeof (open)); off byte close [] = {0xA0, 0x01, 0x01, 0xA2}; Serial.write (close, sizeof (close)); Does it even work with the "Serial MCU controlled switch" plug-in? Yes, this is the standard LC...
by enesbcs
21 Oct 2021, 13:33
Forum: RPiEasy: General Discussion
Topic: Miflora used to work much better..
Replies: 1
Views: 63

Re: Miflora used to work much better..

tempbmx wrote: 18 Oct 2021, 23:31 Since there is no information on rolling back to a earlier version
https://github.com/enesbcs/rpieasy/arch ... a4c7e9.zip
by enesbcs
28 May 2021, 20:14
Forum: RPiEasy: Software
Topic: Migration from ESPEasy to RPIEasy
Replies: 1
Views: 1347

Re: Migration from ESPEasy to RPIEasy

I'd like to migrate from ESPEasy to RPIEasy, but I face some issues. It's seems that not all existing plugins from Arduino board was migrated to python. Raspberry Pi is not Arduino, for example, Raspberry has no analog input pin. But there are several other differences, such as RPI GPIO handling is...
by enesbcs
13 May 2021, 21:29
Forum: RPiEasy: General Discussion
Topic: Publish MQTT mwessages to toggle relay on/off
Replies: 5
Views: 1945

Re: Publish MQTT mwessages

Have you ever use MQTT explorer to monitor your MQTT host ? Not sure why i want to do that. Am using home assistant Well, I am a Domoticz user. What is the "P029 Output helper plugins" and where can I fine it? The same place where every plugin exists: in Devices tab https://i.ibb.co/WpGG3...
by enesbcs
13 May 2021, 18:57
Forum: RPiEasy: General Discussion
Topic: Publish MQTT mwessages to toggle relay on/off
Replies: 5
Views: 1945

Re: Publish MQTT mwessages

How can I Publish messages in RPIEasy on a raspberry. Please be a little more specific. Do you want to send an mqtt message FROM rpieasy to a sprinkler system, or do you want to RECEIVE mqtt messages and change a GPIO state according it? If you want to receive, you can add a Generic MQTT controller...
by enesbcs
06 May 2021, 23:04
Forum: RPiEasy: Hardware
Topic: Question about switch function.
Replies: 4
Views: 2149

Re: Question about switch function.

Premise: gpio 12 is assigned as input switch, pushbutton active on high. Same gpio/pushbutton is used to wakeup LCD, as "Display button:". Short press wake up the LCD.Now we want to use longpress function of same gpio,something like that: 1st longpress enable task 1, 2nd longpress disable...
by enesbcs
12 Apr 2021, 17:52
Forum: RPiEasy: General Discussion
Topic: Sunrise/sunset
Replies: 9
Views: 2030

Re: Sunrise/sunset

I tried %sunrise+3h% ..so it should start at 09:31..but no success... You write %sunset% for the first time: On Clock#Time=All,%sunset% do sendTo,9,gpio,12,1 endon which should work, please stick to the original problem. "+3h" and so on is not programmed into RPIEasy so they are not work,...
by enesbcs
12 Apr 2021, 07:13
Forum: RPiEasy: General Discussion
Topic: Sunrise/sunset
Replies: 9
Views: 2030

Re: Sunrise/sunset

zerocool59 wrote: 12 Apr 2021, 06:39 I'm so sorry..
It 's of course 6":"17
My fault.. :?
Wer lesen kann ist klar im vorteil ;)
I see, and does it have a leading zero? 06:17 ?
if not, try to update to latest RPIEasy version.
by enesbcs
11 Apr 2021, 18:43
Forum: RPiEasy: General Discussion
Topic: Sunrise/sunset
Replies: 9
Views: 2030

Re: Sunrise/sunset

zerocool59 wrote: 11 Apr 2021, 12:17 Variables are 6.17 and 20.01 ..
"." instead of ":" may be a huge issue, for some reason your locale has override requested %H:%M setting. Other time string on variables pages showed with colon? ":"
by enesbcs
11 Apr 2021, 18:20
Forum: RPiEasy: Software
Topic: Change Sensor value
Replies: 2
Views: 1072

Re: Change Sensor value

Hi, I have a small problem: I am measuring waterpressure, value goes in ADS0#Wasserdruck. Works fine - but: if no water is flowing the values swings around 0 (-0.1, 0,04 and so on). There are a lot of possibilities. I guess you are using an Analog ADS1115 device. You can either set decimals to zero...
by enesbcs
11 Apr 2021, 14:13
Forum: RPiEasy: General Discussion
Topic: Sunrise/sunset
Replies: 9
Views: 2030

Re: Sunrise/sunset

zerocool59 wrote: 11 Apr 2021, 12:17 Thank you for your answer...
GPS are set...
Variables are 6.17 and 20.01 ..
I will keep on trying....
Please include the code that is not working for you.
by enesbcs
10 Apr 2021, 16:15
Forum: RPiEasy: General Discussion
Topic: Sunrise/sunset
Replies: 9
Views: 2030

Re: Sunrise/sunset

Hallo @ all.. My problem is that sunrise and sunset command doesn't work . Suntime is installed and systemvariables are okay. I have no knowledge about these commands. suntime and sunrise are variables. If GPS coordinates are saved, they have to work, this is mine: %sunrise% 05:59 %sunset% 19:16
by enesbcs
05 Apr 2021, 09:25
Forum: RPiEasy: Hardware
Topic: Question about switch function.
Replies: 4
Views: 2149

Re: Question about switch function.

When I press the switch quickly the state toggles from 0 to 1 or vise versa and stays that way. When I press the switch for a couple seconds it toggles from one state to another and then back to where it was. If there are some unexpected effect between quick and slow methods, you can try to change ...
by enesbcs
16 Mar 2021, 15:42
Forum: RPiEasy: Software
Topic: P212 Dashboard plugin
Replies: 10
Views: 4630

Re: P212 Dashboard plugin

Thank you. I tried it yesterday. Is there a plug-in to compile yourself for espeasy? I do not understand the question, it's in micropython. How do you want to compile it for espeasy? Only 12 devices can be used in mpyEasy and many sensors are missing, for example SGP30, MPU 6050 or PCF8574. I've ad...
by enesbcs
10 Mar 2021, 19:45
Forum: RPiEasy: Software
Topic: Initial thoughts
Replies: 8
Views: 2671

Re: Initial thoughts

FluffyChicken wrote: 10 Mar 2021, 11:35 My main problem is whenever I stop RPIEasy, it stops the fan on the SDS and that nad a fan start triggers a power pule down the 5V and reboots. So a right royal pain to work with.
Maybe a larger capacitor between VDD and GND helps this problem.
by enesbcs
08 Mar 2021, 23:15
Forum: RPiEasy: Software
Topic: Initial thoughts
Replies: 8
Views: 2671

Re: Initial thoughts

Just noticed in the Particle Sensors you listed, you have MCU680, that a BME680 with a microcontroller (STM32) on it to provide a serial output with iirc bsec's but it's limited and not sure it can be updated or changed to eVOC. Else it's just an i2c BME680, it is not a Particle Sensor, so confused...
by enesbcs
08 Mar 2021, 23:08
Forum: RPiEasy: Software
Topic: Initial thoughts
Replies: 8
Views: 2671

Re: Initial thoughts

Perhaps drop the RPi naming? As I implies its Pi targeted and would be specific. RPi was the first system supported. Now it can run on Orange Pi, Rock PI S, and of course on any Debian running PC with python3. I think about renaming the project but it would cause more trouble than advantage. Especi...
by enesbcs
04 Mar 2021, 19:55
Forum: RPiEasy: Software
Topic: Initial thoughts
Replies: 8
Views: 2671

Re: Initial thoughts

Thank you for your feedback! It seems python3 packages need to be installed globally (sudo) and not as the local user. Yes, this is the reason why "Root rights needed" style alert showing in red color on several places in RPIEasy. Every installation needs elevated rights, not just python p...
by enesbcs
28 Feb 2021, 17:54
Forum: RPiEasy: General Discussion
Topic: How to open web server?
Replies: 2
Views: 1729

Re: How to open web server?

jhoop wrote: 26 Feb 2021, 16:52 Never mind I just figured it out.
localhost:80
Yes. Or any other IP address that the system has.

Code: Select all

10:35:53: Webserver starting at port 80
by enesbcs
20 Feb 2021, 16:54
Forum: ESP Easy: General Discussion
Topic: Maintain date and time in the absence of wifi
Replies: 40
Views: 18201

Re: Maintain date and time in the absence of wifi

I have tried to compile myself using gitpod but I get all sorts of errors that are beyond my skills to fix. I couldn't find a tutorial on how to use it. So unless one of you amazing people will compile one for me a newer build with _P156_DS1307.ino,_P157_DS3231.ino,_P166_WiFiMan.ino, plugin 5, plug...
by enesbcs
14 Feb 2021, 15:59
Forum: RPiEasy: Software
Topic: P212 Dashboard plugin
Replies: 10
Views: 4630

Re: P212 Dashboard plugin

Hej, I don´t find the P212 Dash plugin in the Release mega-20201227 and Release mega-20210114. I always take the compiled *.bin for flashing. Thanks greetings from Sverige ndull P212 is a plugin for RPiEasy, not for ESPEasy... Yes! Although i've backported Dashboard plugin to mPyEasy for ESP32: htt...
by enesbcs
07 Feb 2021, 20:08
Forum: RPiEasy: General Discussion
Topic: Convert uptime seconds to days hours ect
Replies: 4
Views: 2068

Re: Convert uptime seconds to days hours ect

c_s2dhms added to RPIEasy at todays commit.
by enesbcs
07 Feb 2021, 20:06
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 320
Views: 211602

Re: RPIEasy

Global variable support added at today's commit.
by enesbcs
03 Feb 2021, 22:43
Forum: ESP Easy: Hardware
Topic: WT32-ETH01
Replies: 68
Views: 29440

Re: WT32-ETH01

Smotek7 wrote: 03 Feb 2021, 22:24 Flash: ESP_Easy_mega_20210114_normal_ESP32_4M316k_ETH-factory.bin
Connect to wifi and setting lan.
lan set.JPG
Yes, i can confirm. :)
viewtopic.php?p=49536#p49536
by enesbcs
30 Jan 2021, 22:34
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 320
Views: 211602

Re: RPIEasy

Thanks! Issue added to rpieasy.
Mm interesting, so if anyone names its device as "var" or "int" its values can not be accessed anymore.
by enesbcs
30 Jan 2021, 21:00
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 320
Views: 211602

Re: RPIEasy

Hi, I´m searching for a few of hours about this: Next time you can check the wiki: https://github.com/enesbcs/rpieasy/wiki/RPIEasy-implemented-command-list I want to do something like this: on BME280_1#Feuchtigkeit do if [BME280_1#Feuchtigkeit] <> %v1% SendToHTTP 192.168.179.15,8181,/config/xmlapi/...
by enesbcs
27 Jan 2021, 18:37
Forum: RPiEasy: General Discussion
Topic: Convert uptime seconds to days hours ect
Replies: 4
Views: 2068

Re: Convert uptime seconds to days hours ect

EDIT: I see on an ESP unit in the variables page at the bottom "standard conversions" one to do what I want now. Cant figure out how to add that formula in the formula box in the plugin and get it to work. How do I format the actual formula? %value%=%c_s2dhms%(100000 ) doesn't work. (on E...
by enesbcs
24 Jan 2021, 19:23
Forum: ESP Easy: Hardware
Topic: WT32-ETH01
Replies: 68
Views: 29440

Re: WT32-ETH01

If you are trying to use bare LAN8720 modules, a little DIY will be needed on the board, as GPIO-0 has special meaning for ESP32.. I've used LAN8720 with WROVER modules which a little different than WROOM, as WROVER GPIO16/GPIO17 is occupied by onboard PSRAM, but not impossible to do: https://trans...
by enesbcs
24 Jan 2021, 17:53
Forum: ESP Easy: Hardware
Topic: WT32-ETH01
Replies: 68
Views: 29440

Re: WT32-ETH01

What I am still unsure off is that any of the other pins IO19, IO21, IO22, IO25, IO26, IO27 are perhaps not configures wrongly somewhere... I have ordered some spare LAN8720 ic's so I will try to solder one on and see if I can make it to work These pins are the same on every ESP32 as ESP-IDF is not...
by enesbcs
23 Jan 2021, 20:55
Forum: RPiEasy: General Discussion
Topic: Changelog
Replies: 6
Views: 8233

Re: Changelog

In v2.1.023: - C013 ESPEasy P2P controller buffer problems fixed, update if you use that - In Hardware tab, added a new option for autostart with help of systemctl service. Be sure to disable old method, if you use the new, as multiple RPIEasy instances on the same machine will behave strangely. Oth...
by enesbcs
23 Jan 2021, 16:07
Forum: ESP Easy: Hardware
Topic: WT32-ETH01
Replies: 68
Views: 29440

Re: WT32-ETH01

Hi guys, I'm trying to flash or load my own code to this board.... at the moment to try upload the code the board is not getting connected, you know, it keeps like .....____.....____ I'm trying with these serial converters (in the image) without luck, actually I'm reading If GPIO-0 connected to GND...
by enesbcs
21 Jan 2021, 16:53
Forum: ESP Easy: Hardware
Topic: WT32-ETH01
Replies: 68
Views: 29440

Re: WT32-ETH01

Have your tried what enecbs posted above ? Preferred network: Ethernet Ethernet PHY type: LAN8710 Ethernet PHY Address: 1 GPIO MDC: GPIO-23 GPIO MIO: GPIO-18 GPIO POWER: GPIO-16 Ethernet Clock: External crystal oscillator The configuration i'd posted is for "WT32-ETH01" only. "wESP32...
by enesbcs
14 Jan 2021, 21:14
Forum: ESP Easy: Hardware
Topic: WT32-ETH01
Replies: 68
Views: 29440

Re: WT32-ETH01

Checking on Tasmota's work in an effort to save me any headache if possible on the WT32-ETH01 (should be coming in soon) * {"NAME":"WT32-ETH01","GPIO":[1,1,1,1,1,1,0,0,1,0,1,1,3840,576,5600,0,0,0,0,5568,0,0,0,0,0,0,0,0,1,1,0,1,1,0,0,1],"FLAG":0,"BASE&quo...
by enesbcs
11 Jan 2021, 18:03
Forum: ESP Easy: General Discussion
Topic: Serial MCU controlled switch?
Replies: 6
Views: 5986

Re: Serial MCU controlled switch?

Build 20102 - Mega (ESP82xx Core 2_4_1, NONOS SDK 2.2.1(cfd48f3)) GIT version xuryV0.1 xury just compiled its own version from github sources, i guess it is the same as the old ones with Core 2.4.1: https://www.letscontrolit.com/forum/viewtopic.php?p=42226#p42226 In theory it will also work with th...
by enesbcs
05 Jan 2021, 17:15
Forum: RPiEasy: Software
Topic: P212 Dashboard plugin
Replies: 10
Views: 4630

Re: P212 Dashboard plugin

Thats a great idea! I just updated on of my units but can't seem to be able to access it. How do you enable this? Add some tasks that generates data, than add a P212 Dash plugin and setup: - Size (table) - Data type [ Text, Binary input/read only, Switch output/changeable, Meter, Gauge, Slider outp...
by enesbcs
01 Jan 2021, 22:55
Forum: ESP Easy: Software
Topic: LoRa/LoRaWan "Heltec ESP32 LoRa V2" device support
Replies: 8
Views: 7479

Re: LoRa/LoRaWan "Heltec ESP32 LoRa V2" device support

Since my initial post on this thread I have refined my approach to finding a solution for long distance 2-way communication to a remote ESPEasy node. LoRa/Sx1278 P2P controller is available in mPyEasy, if it suits your needs. Its a P2P protocol which follows the same logic as ESPEasyP2P without any...
by enesbcs
01 Jan 2021, 22:31
Forum: RPiEasy: General Discussion
Topic: Changelog
Replies: 6
Views: 8233

Re: Changelog

In v2.1.001:
- support for MCP3208 added
- software-I2C is now appears on hardware page (Raspberry only)
- p2pcom command line utility added for ESPEasy P2P peer detection and for sending commands to them
by enesbcs
31 Dec 2020, 18:32
Forum: RPiEasy: Software
Topic: P212 Dashboard plugin
Replies: 10
Views: 4630

Re: P212 Dashboard plugin

TD-er wrote: 31 Dec 2020, 17:18 Hmm that run button is also a good idea to have in ESPeasy.
Yep, it simply executes taskrun command. :)

And the next button Toggle is for binary outputs only, changes state between 0 and 1.
by enesbcs
31 Dec 2020, 12:26
Forum: RPiEasy: Software
Topic: P212 Dashboard plugin
Replies: 10
Views: 4630

P212 Dashboard plugin

A new plugin is added in the end of the year. With Dash plugin the locally added Tasks can be visualised in a table.
Plugin interval defines the page refresh rate, page can be accessed by IP/dash or can be setted to force itself as startpage.
by enesbcs
30 Dec 2020, 17:59
Forum: RPiEasy: General Discussion
Topic: Changelog
Replies: 6
Views: 8233

Re: Changelog

From v2.0.365, the CSV output also usable in RPIEasy, as in ESPEasy. https://espeasy.readthedocs.io/en/latest/Reference/URLs.html Also the pwm command is modified to work similarly as in ESPEasy. (3rd param is fade) A new customizable local Dashboard is added to display Task values on a separated pa...
by enesbcs
21 Dec 2020, 22:02
Forum: RPiEasy: General Discussion
Topic: webgui usage
Replies: 2
Views: 2664

Re: webgui usage

Enabled GUI ports: 80 8080 8008 591 What happens if I uncheck the first portnumber (80)? When you uncheck port 80, RPIEasy will skip testing port 80, and will use 8080 if it is free (and checked). If it is not, then the next one (that enabled and free) will be tested, and so on. If for some reason ...
by enesbcs
08 Dec 2020, 18:05
Forum: RPiEasy: Hardware
Topic: Senseair S8
Replies: 5
Views: 7225

Re: Senseair S8

I just installed RPIEASY, the Senseair option in the device tabs seems to be missing. Is there a way I could add it? I am very sorry, but RPIEasy is not ESPEasy. There are a lot of plugins which ESPEasy supports but RPIEasy not, and a lot of that RPIEasy supports but ESPEasy not. I guess you can us...
by enesbcs
02 Dec 2020, 22:30
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 320
Views: 211602

Re: RPIEasy

But I have a problem: I can't open the Hardware tab! When I click on it, the browser waits (with the little circle running for loading) but I never get the display of the tab. (Chrome/Firefox or edge) Is there a solution to get the tab open ? Did you run RPIEasy as root? Did you installed GPIO at d...
by enesbcs
25 Nov 2020, 21:22
Forum: RPiEasy: General Discussion
Topic: Changelog
Replies: 6
Views: 8233

Re: Changelog

From v2.0.330 the SPI connected RC522 RFID reader is now supported. On the other hand, SPI device ID is now stored inside plugin variables, which may brake earlier MCP3008 tasks, please modify these or recreate in case of errors.
by enesbcs
24 Oct 2020, 22:28
Forum: RPiEasy: General Discussion
Topic: Changelog
Replies: 6
Views: 8233

Re: Changelog

Be advised as from today build 2.0.298 the handling of EVERY I2C plugin is a bit different, to support multiple I2C lines in the future. Backup before upgrade, in case of errors either try to recreate I2C devices in RPIEasy and restart, or fallback to previous release: https://github.com/enesbcs/rpi...
by enesbcs
19 Oct 2020, 09:30
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 320
Views: 211602

Re: RPIEasy

Yep, 10.x.x.x is not routable address range. But if anybody get into your network, for example with a help of a cloud-enabled hacked IP camera, than will have a good idea where is your server... But it is unlikely. :)
by enesbcs
18 Oct 2020, 21:12
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 320
Views: 211602

Re: RPIEasy

I have no idea why this is happening but again my (ethernet) network does not seem to work correct. 19:23:00 MQTT controller: xx.0.0.xxx:xxxx connection failed [Errno 101] Network is unreachable At least there are no active network connection available when RPIEasy starting. Maybe the dhcp process ...
by enesbcs
17 Oct 2020, 18:45
Forum: uPyEasy: General Discussion
Topic: Sure is quiet around here.
Replies: 5
Views: 9837

Re: Sure is quiet around here.

Its 2020 now and uPyEasy is still very quiet.

In case anybody wants to experiment with micropython and ESP32, i've backported partially the Python3 based RPIEasy. Very experimental. :)
https://github.com/enesbcs/mpyeasy
by enesbcs
16 Oct 2020, 09:31
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 320
Views: 211602

Re: RPIEasy

2stimpy wrote: 15 Oct 2020, 19:43 Isn't it strange that it is starting the webserver after it tries to connect to the network?
There is nothing strange in the starting of the webserver, as it is unconditional.
Is it wifi connection? Ethernet is connected or not? Which Raspbian release?
by enesbcs
15 Oct 2020, 19:36
Forum: RPiEasy: General Discussion
Topic: RPIEasy
Replies: 320
Views: 211602

Re: RPIEasy

18:31:35 Event: GenMQTT#Disconnected 18:31:35 MQTT controller: xx.0.0.xxx:xxxx:1883 connection failed [Errno 101] Network is unreachable 18:31:35 Event: Network#Disconnected Here is a log after a restart. MQTT is not connected at first, only after pushing the toggle it will connect. Strange, have t...