Search found 8 matches

by luisfcosta
03 Jun 2018, 06:25
Forum: ESP Easy: Software
Topic: Stepper Motor
Replies: 36
Views: 49597

Re: Stepper Motor

Hi there! @Domosapiens, did you use the default settings (for the AccellStepper library) or some specific ones for the 28BYJ And if I may, which values you used for the 2phase - 6wires? ( https://www.ebay.com/itm/1PCS-Used-27mm-2-Phase-6-Wire-Stepping-Motor-With-Gearbox-Gear-Ratio-1-12-/172590534560...
by luisfcosta
05 Mar 2018, 06:39
Forum: Experimental
Topic: Round up...
Replies: 5
Views: 14710

Re: Round up...

Hey there I happen to be looking for a compatible Espeasy for an Arduino/Mega with an ethernet shield and I came across this thread. Would one of you gents be able to share where is this github repository for Espeasy for an ethernet shield? We are looking to interconnect Arduinos and Raspberry Pi's ...
by luisfcosta
03 Jun 2017, 09:00
Forum: ESP Easy: Hardware
Topic: H801 : RGB controller based on ESP8266 avalaible from China
Replies: 134
Views: 182194

Re: H801 : RGB controller based on ESP8266 avalaible from China

Sorry guys, trying to include plugin 105_rgbw into the lates R2.0 dev10, but my arduino IDE keeps throwing error after error (cannot find file, library, etc) Is there a more straightforward way than rearranging my .ino's and .h's + .cpp's? Trying to get my h801 flashed with ESPEasy and the correct p...
by luisfcosta
24 May 2017, 22:49
Forum: ESP Easy: Hardware
Topic: Ebay Wifi Relay boards
Replies: 55
Views: 46546

Re: Ebay Wifi Relay boards

I wanted to provide a follow up and closure to my previous plea for help Situation: Espeasy R120 not stable, causing nodelink R8 to reboot every 10 secs. Espeasy loaded with Arduino source code. Board was also not reacting on MQTT commands. Solution: Upgraded to 147 RC8 using the flash.cmd method. I...
by luisfcosta
24 May 2017, 21:34
Forum: ESP Easy: General Discussion
Topic: ESPEasy Basics
Replies: 10
Views: 19525

Re: ESPEasy Basics

I think I found an answer! Once I upgraded to 147 RC8 using the flash.cmd method, I can control my relays using mosquitto_pub -t "{devicename}/gpio/16" -m "1" [or "0"]. My MQTT broker receives the same message, so I am able to keep track of what is ON of OFF. At least t...
by luisfcosta
24 May 2017, 16:50
Forum: ESP Easy: General Discussion
Topic: ESPEasy Basics
Replies: 10
Views: 19525

Re: ESPEasy Basics

Hi Cerino

I am also experiencing the same with stable release 120. Did you find a solution to your problem?
My nodemcu does not act on broker messages - using OpenHAB MQTT solution, despite it's not stable (looses connection to the broker)
I am playing with a linknode R8 and espeasy 120
Thanks
by luisfcosta
22 May 2017, 08:29
Forum: ESP Easy: Hardware
Topic: Ebay Wifi Relay boards
Replies: 55
Views: 46546

Re: Ebay Wifi Relay boards

My 340 drivers are not working with me on my Windows 10 And I did tried with 4M/64SPIFFS but with the same result The board compiles and uploads well with the Arduino IDE and works very well until, after I have configured the 7th relay, starts rebooting every 10 secs In another time it was when all ...
by luisfcosta
20 May 2017, 07:47
Forum: ESP Easy: Hardware
Topic: Ebay Wifi Relay boards
Replies: 55
Views: 46546

Re: Ebay Wifi Relay boards

Hi guys I notice this thread mentions LinkNode R8 so I am trying my luck here After I uploaded the Easpeasy R120 to a R8 board, and start configuring it, I notice after the 6-7th device (switch input), the board starts rebooting continuously, making it impossible to use. Has anyone experienced the s...