Hi,
thanks for the info.
Can you please provide the lua script?
I have no idea how to do it.

br
Carsten

Hallo all, I have a Problem to set up domoticz for dimming. I want to use the PWM from ESP easy to dimm a LED. How can this be done via domoticz? I have created a Dimmer in domo but i can Not hand over the value for the http String. ( also Not new calculated value which fit the 1024 Max). Can anybod...

Hello,
I have now tested it. It works fine, thanks a lot!

Best wishes to the team, great job done.

br
Carsten

Hey,
thats sounds good. I will check it later when I´back from work.

br
Carsten

Hi,
there can be many blocking points:
1.can you see in the ESPeasy if it shows the right status of the switch? (right GPIO, Pullup)
2. do you have put in Domo the switch online?

br
Carsten

Hi Martinus,
You are right. It's not so easy. Until it will be implemented i make the change in the Source For me. I need it only in one ESP. The other ones can get the normal versions. Thanks for the Investigation.

Bei
Carsten

Hi, yes, it is not possible to it with Domo, the reaction time is to long and is varying from time to time over the network. I have "Eltako Dimmer" in place, these one can do the following on 230V. You will push the button for a maximum of 0,6 Seconds, then the light will dim up to the las...

Hello team, will it be possible to implement the following thing? with the command e.g. "http://192.168.1.81/control?cmd=GPIO,5,1" the output pin will be set to high for a previous defined time range. (Also inverted will be good to manage negative logic. Time range should be configured in ...

Hi, I have had for a few minutes tried to connect the DHT22 to the ESP. The first 2 minutes I get also no data. After warm up of the DHT22 it shows the values very well. Do you have checked if the 5V are available on the DHT? Do you use the right 3 pins? (one will not be connected) Which ESPeasy ver...

Hello all, I want introduce my self little bit. First, I found the ESP easy project very great and useful. The support and reaction time is great. THX Now to my person: I´m coming from Germany and are 42 years old. My experience in home automation is small, I hope it is growing very fast so that I c...

Hi, I have tested it but it didn´t work. Using R25 What Ia have done: 1. going to "Tools" -> Settings:List nothing viewed in the list (tested under WIN with IE10, Firefox and on my MAC) 2. Save the config file works 3. Upload config file also works 4. reboot 5. going to "Tools" -...

Hello all,

wow, very good. It is working well so far and I will install it today in my homecontrol for testing.
Thank you very much!!!!

br
Carsten

PS: now the next component will be tried: DHT22

Hello,
yes, it was no bug and a feature request.
I will test it today, in a few hours when the kids were sleeping
Thanks in advance
Carsten

Hi,
i will test it again with the new release.
I hope I can give you an answer tomorrow.
Thanks for your investigation and support.

br
Carsten

Hello all, I hope any body can help me. I accounter a problem by the config of an push button. I have running domoticz and an ESP8266 Version 12 (Olimex dev board and also tried an ESP01). Everything is configured in domoticz, like an normal switch. If you press the virtual button in domom you can s...

Hello together, I have flashed the latest version, 23 on my Olimes dev board and counter some Problems: 1. Mainsettings: changing the WPA AP Mode Key doesn´t work on my unit, in version 20 there was no problem--> have only I the problem? 2. Tools: settings-load safe list didn´t work correctly: save ...